Router accessories





	All-In-One Router Plate Kit

3/8" thick phenolic supports any router. Two removable rings give three different bit openings (3-7/8", 2-5/8", 1-3/16"). Note: 1-3/16" opening is designed to hold Porter-Cable® style guide bushings. The steel starting guide pin allows routing curved work. The plate is approximately 9" x 12" with pre-drilled table mounting holes. Includes magnets and adjusting screws for securing and leveling plate. Also includes concentric rings on bottom of plate for easy alignment when installing router. All-In-One Router Plate Instructions (PDF) All-In-One Router Plate Kit #9338 .................... $34.95 Replacement Rings & Guide Pin #9329 ................................SALE $10.95
		All-In-One Router Plate Kit





Aluminum Router Plate

Our 1/4" thick aluminum router table insert will support the heaviest of routers, without plate sag. The plate is about 9" x 12" and includes leveling screws and magnets to secure the plate in the table. Includes three separate insert rings with attaching screws which provide opening sizes (3-1/4", 1-7/16", 1-3/16" for template guides and a blank insert ring to create your own size). The steel starter pin is for routing curved pieces. Pre-marked mounting hole indentations provided for most popular routers. (The plate is not pre-drilled). Aluminum Router Plate Instructions(PDF) Aluminum Router Plate #9334 ............................................. $65.95 Replacement Rings & Guide Pin #9330 ....................................SALE $10.95
						Aluminum Router Plate





Installation Template & Bushing Kit

The router plate must fit perfectly, and this kit makes it easy! Includes a masonite routing template, guide bushing (fits Porter-Cable® style baseplate opening) and instructions. Requires 1/2" straight bit. (Items #5477 or #7777). #9331 ..........................................SALE $20.95
					Installation Template & Bushing Kit



SuperTuff Router Mounts

Replace your router's plastic base with long lasting "SUPERTUFF" material. These clear, shatter resistant squares can be drilled, cut or routed as needed to make your router table inserts, safety shields, router fixtures or projects. Measures 11+" square and is available in 1/4" or 3/8" thickness. 1/4" Super Tuff Router Mount #9095 Reg. $17.95........................SALE $14.95 3/8" Super Tuff Router Mount #9097 Reg. $21.95........................SALE $18.95


Universal Centering Alignment Pin

This handy set-up tool is designed to fit both 1/4" and 1/2" router collets, and center the baseplate to the collet. It’s vital for inlay work, pattern router, and using any precision fence system. It will also indicate the exact center of any bit cut, which is important when locating grooves and dadoes. The centering /alignment pin can be used to check run-out on drill press, mill and lathe chucks. Universal Centering Alignment Pin #9054 Reg. $14.00..........................SALE $5.95

MLCS Router Collet Extension

For 1/2" collet routers! Give your router bits an additional 2-1/4" (for #9465 or 2" for #9473) when you extend them through the router table top with our router collet extension. Eliminate the dangerous temptation of withdrawing the shank from the collet in order to raise the bit and to "provide the full depth of cut." The router collet extension makes it possible to use all diameters of 1/2" and 1/4" shank bits safely. Place the router collet extension shank in the 1/2" router collet and the router bit shank in the extension collet and tighten both. Wrenches and instructions included. Note that for previously sold item's #9464 and #9468 the large diameter is the same as in the chart below. NOTE: Will not work with 1/4" collet routers.

Router Collet Instructions(PDF)

ROUTER COLLET EXTENSION for 1/4" and 1/2" shank bits
Item #	Type	Large Diam.	Reg. Price	Price
#9465	For 1/2" shank bits	1-3/16"	$~~42.90~~	$29.95
#9473	For 1/4" shank bits	7/8"	$~~42.90~~	$29.95

Wrench Sets for previously purchased Router Collet Extensions are now available for both 1/4" and 1/2" shank.
#9466 1/2" Shank Wrench Set.....SALE $7.95

#9474 1/4" Shank Wrench Set.....SALE $7.95

WEB SPECIAL! Get BOTH 1/4" and 1/2" Router Collet Extensions Plus a 3 Piece Wrench Set
#1721	2 ROUTER COLLETS and 3 WRENCHES Regular Price $~~59.95~~	$49.95




Brass Router Height Set-Up Kits

Perfect for router, shaper and table saw set-up. Soft metal Brass Bars won't splinter or chip your router bit or saw blade if they accidentally hit the cutters. BRASS MULTI SIZE SET-UP KIT 2-3/8" bars allow accurate depth adjustments in 6 sizes (1/16", 1/8", 3/16", 1/4", 3/8", 1/2"). Attached to keychain. #9718 list $20.00........................ONLY $15.95 SQUARE 4" LONG BAR KIT Allows depth adjustments in five sizes: (1/8", 3/16", 1/4", 3/8", 1/2"). 4" Long Bars fit across router opening. #9717 Square Bar Kit...................ONLY $24.95

Router Table Power Switch

The Router Table Power Switch allows safe and convenient on/off control of 120V AC routers or tools. Mounts quickly and prevents reaching under the table to turn off your router (WHICH GREATLY INCREASES SAFETY!). Just plug your router into the Power Switch and plug the Power Switch into the wall outlet. Removable lock even prevents unauthorized use. 67" power cord. Maximum 15 amps. 9079
#9079 List. $41.50............... $24.95


No rating yet... Be the first to rate this product!

all customer reviews and ratings

No rating yet... Be the first to rate this product!

Safety "Router Table" Power Switch

NEW Safety Lockout Feature! This convenient, mechanical push button switch features a large paddle "STOP", to allow you to quickly shut off power to your 120VAC machinery. Placing the switch where you can use your hip or knee to bump it into the "off" position gives you the freedom to never take your hands off the workpiece to turn off the machine. Just plug your router into the Safety Power Switch router cord and plug the Safety Power Switch power cord into the wall outlet. Surface mounts quickly and easily. Works with routers 3-1/4 HP or less.
#9078 ................................ONLY $29.95


Rated: Review this product...

all customer reviews and ratings

Average Customer Rating: (1 reviews)
Add your own review for this product

Greg in KY (5/5), Jan 14, 2010

By Greg Cundiff (Crab Orchard Ke US)

I recently purchased a new router table and fence (item #2392) and the stand, I was in desperate need of a safety switch. I will admit I was a little leary at first, thought it looked a little cheap, we all know what that usually means. O'boy was I surprised when it showed up at my doorstep. I was even more surprised to see that I could add two additional cords to this switch, which will be handy for running the router and a shop-vac all from one switch. But before you get your hopes up, the additional cords and hardware to install them in this switch is NOT included, but can be obtained from nearly ALL home improvement or hardware stores. However, I did have a little trouble with how rough the switching action was, I took the switch apart and a little sanding to the angles on the contact bar and its as smooth as anyone could ask for. MLCS Thanks again for such a great product at such a good price.

Add your own review for this product

Safety "Motor" Power Switch

Now you can replace or upgrade the power switches on your woodworking machinery. Exactly the same switch as above but needs to be hardwired to the router motor and to power cord. Surface mounts. Max. 20 amps. Will work with 110 or 220 volt motors.
#9072 ................................ONLY $21.95


Rated: Review this product...

all customer reviews and ratings

Average Customer Rating: (3 reviews)
Add your own review for this product

Mechanical Engineer / Physicist (1/5), Feb 19, 2010

By Thomas Tyrie (Francestown NH US)

Very poor quality switch. Rough initial switching action. After a dozen switch cycles the switch failed to toggle any more. When opened up switch found plastic switch casing was broken during initial assembly of switch. Also the button castings were molded with a mismatched parting line in the mold producing an uneven surface. This uneven surface caused the initial switch action to be sticky. Another reviewer (see Safety "Router Table" Power Switch review) observed the same issue and resolved the problem by sanding this surface smooth. That review prompted me to open the switch and attempt the same repair only to discover a damaged switch. My final solution - adapted cover plate to the original Delta USA manufactured high quality switch and electrical box. This task was not straight forward since the Safety Motor Power Switch Cover mount holes did not align with those of a standard metal electrical box.

Last Comments: Price was good. Disappointed by poor switch quality. Buyer should not have to modify switch parts to achieve smooth action. While the cover plate and plastic electrical mounting box are not industrial quality they are still good quality parts.

Jim from Ohio (5/5), Dec 15, 2009

By James J. Petelin (Massillon OH US)

I replaced a bad toggle switch on my old Delta Contractor Saw with this one. The Delta replacement switch was more than twice the cost and not nearly as safe. This is a "no brainer" purchase if you need to replace your switch or if you want to upgrade an existing switch - definitely Five Stars!

'Ol WC from Michigan (5/5), Oct 9, 2009

By Wes Crawford ( Mi US)

I have installed the hardwired version on my table saw/router table extension. Many use this paddle switch mounted on the side of the table. Mine is also on the side, but faces to the front on an angle bracket at exactly the right height for thigh operation. This allows me to keep both hands on the workpiece at all times. This is a 2 pole switch, and I use the second set of poles on the switch to operate my shop vac. I installed a double duplex receptacle set-up adjacent to the switch which is handy for the vac and other tools. The switched receptacle is for the vac and is controlled by an adjustable "off delay" cube relay mounted in the magnetic starter for my table saw that allows the vac to run a preset length of time after the router is turned off to clear the hose.

When I'm done with the router, I just plug the vac in "next door" in the other non-switched receptacle to use with other operations.

The switch has worked flawlessly, and I highly recommend it. In fact, I wish it was available in a momentary contact version to use with the table saw. I could use this maintained contact version, but would have to give up the benefit of no auto restart after a power outage. Unfortunately, where I live, these are all too common.

Offered for the convenience and safety of all my fellow wood butchers,

Wes Crawford

Add your own review for this product

Miter T-Fence

Miter Gauge not included.

Miter T-Fence (PDF)

Add the ULTIMATE fence and stop system to your miter gauge! Miter-T-Fence will insure dead-accurate miter cuts and provide support close to the blade to eliminate tear-out. The adjustable, extruded aluminum fence increases the face of your miter gauge to 2-5/16" high x 22 long. The built-in extension bar increases the stop capacity to 36". The included nylon stop adjusts along the full length of the fence, and locks tight for perfect repetitive cuts. Miter Gauge not included.
Miter T-Fence
#9467 Reg $64.95...............................SALE $54.95

BUY BOTH & SAVE $10!

Miter Gauge and Miter T-Fence Set
Includes #9458 and #9467
#9457 .......................$79.90

Miter Gauge

WEB SPECIAL! SAVE $5. Our Miter Gauge features a full 60º travel both left and right with adjustable positive stops at both 90º and 45º. The 3/4" x 3/8" x 18" miter bar securely locks into a miter T-slot or will fit standard miter slots.
Miter Gauge
#1725 ......................................SALE $29.95

BUY BOTH & SAVE $10!

Miter Gauge and Miter T-Fence Set
Includes #9458 and #9467
#9457 .......................$79.90

Clamping Miter Gauge

Useful and accurate when making crosscuts or routing end grain on table saws. Squeezing the pistol grip engages a downward pressure clamp, securing your stock firmly in place. Fits any standard 3/4" x 3/8" miter slot. The positive adjustable stops at 90º and 45º, left and right, are useful for both left and right tilt table saws. Includes adjustable stop block, great for repetitive length cuts. 4" Maximum stock thickness. Bar extends to 12".
Clamping Miter Gauge
#9456 ......................................SALE $44.95

BUY BOTH & SAVE $10!

Clamping Miter Gauge and Miter T-Fence Set
Includes #9456 and #9467
#9453 .......................$89.90



T-Track Hold Downs
Convenient metal T-track clamps work on any t-track that accepts a 1/4" or 5/16" hex head bolt. The T-shaped base and 1" round brass hold down will secure stock from 1/4" to 2" thick against your table, or use on jigs that have a T-track. Use on a drill press table to secure the work piece. Can also be used on a drill press or router table fence to mount stop blocks onto the T-track in the fence face. Sold as a pair. #9441 Reg. $34.95 ...................SALE $29.95

Miter T-Track & T-Bar

WEB SPECIAL! SAVE $5 for #1702! Works with standard 3/4" x 3/8" miter gauges with or without a T-slot. Our track is great for shop built router tables that are not equipped to handle a miter gauge. You can add a miter or sliding fixture to anything that can be routed out to fit the Miter T-Track work bench, table saw extensions, drill press tables, and band saw tables. The miter T-bar slides into the miter track or miter slot in your table saw. The T-bar can be used to make sliding jigs and other fixtures throughout the shop. Add a lock down knob by drilling and taping the T-bar, there is no end to the possibilities. Use #7785 (1-1/4" Straight bit) to make the groove for the Miter T-Track. T-Track length may vary up to 1/8".

Miter T-Track and T-Bar
A 32" #9871

Miter T-Track ...........................SALE $16.95

A 48" #1702

Miter T-Track ...........................SALE $19.95

B 32" #9872

Miter T-Bar ...............................SALE $16.95

32" MITER T-TRACK & BAR SET
Includes One Of Each... BUY BOTH AND SAVE! #9873....................................$28.95


Combo T-Track / Miter T-Track
Our combo T-Track/Miter T-Track lets you use your miter gauge or tenoning jig, plus T-Track accessories on your router table, band saw table or table saw extension. The T-Track accepts any accessory that uses a 1/4" hex head bolt, such as featherboards, stop blocks or hold downs. The Miter track accepts a standard 3/4" x 3/8" bar or sliding T-Bar. 32" length may vary up to 1/8". 32" Combo T-Track/Miter T-Track #9859.....................................................SALE $24.95


Miter T-Track Accessory Kit
Create custom jigs and fixtures with our Miter T-Track slot locking kit. Lock all types of featherboards onto table saws, router tables and band saws. The T-bar will fit any 3/4" x 3/8" miter T-slot groove. Instructions are included for attaching to a featherboard or making a circle cutter for your router. Includes: 2 pcs Aluminum T-nuts (1-stop, 1-pivot) 2 pcs 1/4"Flat Head Screws 2 pcs 1/4" Triangle thru Knobs\ 1 pc 1/4" Set Screw (1/4" hex) 2 pcs 1/4" Washers 1 pc 1/8" Allen Key 1 pc plastic Spacer 1 pc 4x20mm self-tapping Screw Miter T-Track Accessory Kit #9870Miter T-Track & T-Bar Accessory Kit.............$9.95

Router Bits and Woodworking Products

Join the E-Club!

All-In-One Router Plate Kit

Aluminum Router Plate

Installation Template & Bushing Kit

SuperTuff Router Mounts

Universal Centering Alignment Pin

MLCS Router Collet Extension

Brass Router Height Set-Up Kits

Router Table Power Switch

all customer reviews and ratings

Safety "Router Table" Power Switch

all customer reviews and ratings

Safety "Motor" Power Switch

all customer reviews and ratings

Miter T-Fence

Miter Gauge

Clamping Miter Gauge

T-Track Hold Downs

Miter T-Track & T-Bar

Combo T-Track / Miter T-Track

Miter T-Track Accessory Kit